|
| Tractor Mounted Drilling Rigs - KLR TC - 40, Core Drill Rig |
|
| TECHNICAL SPECIFICATIONS |
|
| Description |
| KLR, TC-40, is a Tractor Mounted Top drive all
Hydraulically operated core Drilling Rig extracting main power from
Tractor Engine, is designed for Geo-technical investigation (Geological
survey), soil sampling application capable of drilling to a maximum
depth of 150 Mt. (500 feet) |
| Drilling Capacity |
|
| Core Drilling |
SI |
FPS |
| Drilling Sizes & Drilling Depths |
|
|
| NW Drilling (core 54.0 mm) |
150 m |
500 feet |
| NX Casting (88.9 mm Drilling) |
50 m |
150 feet |
|
Mast Structure
Strudy structural channel type Mast of electrically
welded construction, main members made out of heavy duty structural
steel channels reinforced with suitable cross members, so that it will
be strong enough to withstand the varying drilling loads.
| Mast Length |
5500 mm |
| Rotary Head Travel |
4500 mm |
| Centraliser Opening |
200 mm |
| Raising and Lowering |
With hydraulic cylinder |
| Max. Rod handling Capacity |
3 m |
|
Tophead
Rotary Drive
Heavy-duty Hydraulic driven Top head Rotation unit
having infinitely variable speed (0 to 500rpm) will be provided. This
unit travels on the Mast and is of sturdy construction to absorb sudden
& varying shock loads generally encountered during drilling
operations.
| Output Speed |
0-500 rpm |
| Output Torque |
60 Kgm |
| Types of Gears |
Spur Gears |
| Drive Motor type |
OMT 200 / Orbital |
| No. of Motors |
01 No. |
|
Feed System
Feed system is provided with adequate travel for handling drill pipes upto 3.0
Mt l
ong.
The feed and hoist are actuated by a suitable Hydraulic Cylinder with wire rope and pulley arrangement.
The feed system has the following capabilies
| Max. Pull Up Force |
4500 kgf |
| Max. Pull Down Force |
2400 kgf |
| Max. Pull Up Speed |
40 m/min |
| Max. Pull Down Speed |
65 m/min |
| Reeving Ratio (Wire Rope) |
1:3 |
|
The feed system will be incorporated with
Hold back arrangement to control and limit weight on bit, rapid and
slow feed arrangement to suit the variable ground conditions.
Hydraulic System
| Max. Operating Pressure |
160 kg/cm2 |
| Hydraulic Tank Capacity |
300 Lts |
| Filtration (Nom.) - Return Line |
10 microns |
| Hydraulic Oil Cooler |
40 GPM
(Fin type Oil to Air) |
|
Prime Mover
Power required for the rig Hydraulics shall be drawn from the tractor engine through the out put shaft (PTO).
Stabilizers (Jacks)
System consists of three Hydraulic Leveling Jacks
with 'Reverse flow restricted valves to ensure safe operation. Two
numbers are at the front (Operator side) of the rig controlled by two
separate valves and one jack at the rear side of the rig controlled by
a single valve.
| Type |
Hydraulic Cylinder |
| No. of Jacks |
3 Nos |
|
Breakout Wrench
The Drill Rig is equipped with Hydraulic breakout wrench for tightening and loosing of Drill pipes and The Hammer.
| Cylinder Bore Diameter |
80 mm |
3 Inch |
| Stroke |
300 mm |
12 Inch |
|
Water Injection Pump
Triplex plunger pump shall be used for DTH Drilling.
| Capacity |
36 lpm |
| Max Pressure |
40 bar |
|
Winch Assembly
Hydraulically operated wire line winch is mounted on mast to handle the Casing Pipes, Drill pipes and other handling tools.
| Line Pull (Bare Drum) |
800 kgf |
| Line Speed (Bare Drum) |
40 mt / min |
|
Air Compressor
Air compressor of suitable capacity as mentioned can be used for carrying out the DTH drilling activity.
| Air Compressor |
450 cfm / 150 psi |
| Make |
Reputed make |
|
Note: The compressor shall be mounted on separate two wheel single dummy axle waith mechanical stabilizers quantity one number.
Air Line Lubricator
Air line lubricator of capacity mentioned below shall be mounted for the supply of lubricating Oil to the hammer.
| Capacity |
600 cfm / 200 psi |
| Make |
Reputed make |
|
 |
KLR Drilling Rigs can be supplied in custom-built
models in various Configurations as indicated below, Mounting features
to suit all special requirements and Technical specifications can be
offered accordingly |
|
KLR TBH -40, capable of drilling up to 50 Meters (150 feet) in case of Blast Hole Drilling |
|
| |
|
